Yonkers, NY · Commercial Kitchen Repair
Hobart Repair in Yonkers
Hobart Commercial Equipment Specialists
Hobart is the standard in commercial warewashing and food prep — door-type and conveyor dish machines, the legendary planetary mixers, slicers and food processors. A down Hobart dish machine stops your turnover; a jammed mixer or slicer stalls prep. We repair the wash systems, drives and controls that keep Yonkers kitchens moving.
- STATUS
- Dispatch ready
- RESPONSE
- Same-day · 24/7
- RATING
- 4.9★ (612)
- WARRANTY
- 90-Day Parts & Labor Warranty
- COVERAGE
- Yonkers + Westchester
Serving Yonkers
Hobart Commercial Equipment Specialists
The short answer
Hobart Repair in Yonkers typically runs $250–$900 — the $95 diagnostic is waived when you approve the repair. Most jobs finish same-day with OEM-spec parts, backed by a 90-Day Parts & Labor Warranty, with 24/7 emergency dispatch. Call (914) 449-5646.
Warewashing and prep are the invisible backbone of a Yonkers kitchen: when the Hobart dish machine stops, plates back up and service grinds to a halt; when the mixer or slicer fails, prep stops before doors open. And a dish machine that won't reach sanitizing temperature is a direct health-code failure. We treat these as priority calls, carry the pumps, heaters and drive parts these units need, and verify sanitizing temperature and safe operation before we leave.
Why Choose Us
- Warewashing and food-prep specialists — dish machines, mixers and slicers
- Sanitizer-temperature and chemical-concentration verification for compliance
- OEM-spec pumps, motors, heaters, gears and controls stocked
- Same-day and 24/7 emergency dispatch
- Slicer and mixer safety systems checked on every visit
- 90-day parts & labor warranty
Maintenance Tips
- Descale the booster heater and tanks regularly so the machine reaches sanitizing temperature
- Clean wash and rinse arms and jets to maintain spray pressure
- Check and top up mixer transmission oil; listen for gear noise
- Keep slicer blades sharp and verify safety interlocks work
- Confirm final-rinse temperature or sanitizer concentration daily for compliance
- Clear scrap trays and drains to prevent clogs and drain faults
Quick facts
| Service | Hobart Repair |
|---|---|
| Turnaround | Same-day in most cases |
| Diagnostic | $95 — waived on approved repair |
| Warranty | 90-Day Parts & Labor Warranty |
| Most common fault | Diagnosed on site |
| Serving | Yonkers, Mount Vernon, New Rochelle, White Plains & Westchester County |
What repairs cost
Straight pricing, no surprises.
These are typical all-in market ranges for parts and labor on commercial kitchen equipment across Yonkers and Westchester County. Your exact price is quoted on site after diagnosis — the $95 service call is waived when you approve the repair.
| Repair | Typical range |
|---|---|
| Diagnostic / service call | $95–$165 |
| Commercial reach-in / prep refrigeration repair | $250–$900 |
| Control board / electronics repair | $300–$950 |
Ranges are estimates for reference, not a quote. OEM-spec parts · 90-Day Parts & Labor Warranty.
How a call goes
One commercial specialist. Fast dispatch. Verified fix.
- 01
Call & dispatch
Reach a real person at (914) 449-5646 — most Yonkers jobs get a same-day slot, and emergencies get 24/7 priority dispatch.
- 02
Diagnose the fault
We test the actual failing part and system — sealed system, gas train, harvest cycle — not guess-and-swap.
- 03
Fix with OEM-spec parts
Common commercial parts ride on the truck, so most repairs finish in a single visit.
- 04
Verify & warranty
We verify temperatures and safety, back every repair with a 90-Day Parts & Labor Warranty, and leave you inspection-ready.
Answers
Frequently asked questions
Our Hobart dish machine isn't sanitizing — the rinse gauge won't reach 180°F. Can you fix it fast?
Yes, and it's urgent because a machine that doesn't reach its sanitizing temperature (or proper chemical concentration on low-temp units) will fail a health inspection. The cause is usually a booster heater element, a thermostat/contactor, low incoming water temperature, or a scaled heater. We test the rinse circuit and booster, repair the fault, and verify the machine sanitizes to code.
My Hobart mixer won't turn or is grinding — is it worth repairing?
Almost always. Hobart mixers are built to be rebuilt — worn gears, a bad transmission, a failed motor, or a bowl-lift issue are all repairable, and a rebuilt Hobart outlasts a new economy mixer. We diagnose the drive and transmission and repair it so your prep runs again.
How quickly can you get a down Hobart dish machine back in service?
Same-day in most cases, with emergency priority — a dead dish machine backs up your whole operation. We stock common wash/rinse pumps, motors, heaters, contactors and controls to finish many warewashing repairs on the first visit.
Our Hobart slicer won't cut cleanly and the blade seems dull — can you service it?
Yes. We sharpen or replace the blade, service the drive and belt, and check the safety interlocks and guards so the slicer cuts cleanly and operates safely. Slicer safety systems are not optional — we make sure they work.
Do you offer maintenance contracts for Hobart warewashing and prep equipment?
We do. Descaling booster heaters and wash tanks, checking pumps and dispensers, verifying sanitizing temperature, and lubricating mixer drives on a schedule keeps Hobart equipment reliable and inspection-ready across a busy Yonkers kitchen.
Verified reviews
Rated 4.9★ by Yonkers operators
612 verified reviews
“Outstanding Hobart repair service! The technician was very knowledgeable about Hobart appliances and fixed our door-type dishwashers quickly. Highly recommended!”
“Our Hobart dish machine wasn't hitting the 180-degree sanitizing rinse and we had an inspection coming. The tech traced it to the booster heater element and a bad contactor, repaired it same day, and verified the rinse temperature in front of me. We passed with no issues. Real commercial expertise.”
“Our 60-quart Hobart mixer started grinding and I thought we'd have to buy new. They rebuilt the transmission and replaced worn gears for a fraction of a new machine, and it runs like new. Honest advice and real skill — they could have upsold us and didn't.”
“Our meat slicer had a dull blade and the safety guard wasn't engaging right. They sharpened it, serviced the drive, and fixed the interlock so it's safe for my staff again. They wouldn't hand it back until the safety worked — I appreciated that.”
Across Yonkers, Mount Vernon, New Rochelle, White Plains and the wider Westchester County commercial corridors, Yonkers Commercial Appliance Repair is the team restaurants, bars and commercial kitchens call when a hobart repair needs a true commercial specialist rather than a residential appliance tech. We diagnose the actual fault — not guess-and-swap — carry OEM-spec parts on the truck for most Yonkers visits, and back every repair with a 90-Day Parts & Labor Warranty. In a commercial kitchen, downtime is lost revenue and lost inventory, so we dispatch fast and verify temperatures and safety before we leave. Call (914) 449-5646 for same-day and 24/7 emergency service.
4.9★ · Yonkers & Westchester County · 24/7
Need Hobart Repair in Yonkers?
Call (914) 449-5646 for same-day & 24/7 emergency service in Yonkers.